Technology

BIFILAR SUSPENSION PDF

ME DYNAMICS OF MACHINERY LABORATORY EXPERIMENTS BIFILAR SUSPENSION INTRODUCTION The Bifilar Suspension is a technique that could . Oscillation of a bifilar suspension Apparatus: Two retort stands/clamps/ bosses, two metre rulers, stop watch, two lengths of cotton thread. two threads. Bifilar suspension. If a rod of moment of inertia I and mass m is hung from two threads of length L and separated by a distance d (Figure 1) and is oscillated in a .

Author: Meztigal Nejas
Country: Liberia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 5 February 2012
Pages: 98
PDF File Size: 19.63 Mb
ePub File Size: 18.68 Mb
ISBN: 361-6-13952-140-6
Downloads: 1625
Price: Free* [*Free Regsitration Required]
Uploader: Moogutilar

With the bar suspended by the wires, the length L was adjusted to a convenient extent and then distance, bbetween the wires was measured.

Repeat the above for seven more different values of D. Do suspenzion tie the threads too tightly as you will need to vary the distance D during the experiment. This also provides another approach to the determination of the moment of inertia of the body.

Posted by JohnWell Academy at From the relationship between the periodic time of oscillation of the suspended bar, and the effective length of the suspension wires the radius of gyration of the suspended bar may be found and compared with suspensoin theoretical value. Chapter 11 The Age of Imperialism.

The radius of gyration and moment of inertia reduced after the length of wire was increased from test 1 to test 2 but increased right after till test 4. Density of the bar steel bar. The experiment is done such that the oscillation was not dampened by carefully tilting the bar before release for oscillations.

Additional table 4 extrapolated from table 2. Beginning of American History. The length L was further adjusted and the time taken for another 20 oscillations was recorded. Sus;ension equation of the angular motion is: Nonetheless, a description of its angular motion is enumerated below. The cords pass through the two small chucks fitted to the top frame and are secured in the bifilar bar by two similar chucks so biffilar by loosening the chucks the cords may be dawn through and their effective length altered.

Most Related  JRC386D PDF

Length of bar l. Reaction Bifilsr Lab Ruler Drop. Laboratory Manual for Phys. Chucks are also in place to alter length of suspended wires.

Bifilar suspension

These readings encompasses the distance between the wires used for the suspension, the length of the wires, the time for the required number of oscillations, the distance between the masses introduced bufilar the experiment, and so on. Bifjlar is done by suspending two parallel cords of equal length through the object examined. In this case the body under investigation is bolted to the center of the suspended bar and the periodic time of the combined bar and body measured.

Documents Flashcards Grammar checker. This is called the auxiliary mass method but for this experiment, our analysis would be on just the generic bifilar suspension approach.

There was a problem providing the content you requested

All these and lots more provide the avenue for determining the radius of gyration and the moment of inertia. What is the basic assumption that is based on assuming a small angle of oscillation? Mass of each added mass. Set up bifilag above apparatus with two lengths of thread of equal lengths approx. Then the values obtained from experiment will be compared with the value obtained analytically, using the geometry and dimensions of the beam.

Why is it important not to let the total time measurement see stage 4 fall below about 10 seconds?

Most Related  ALASTAIR FUAD-LUKE PDF

From equation 10 above. Newer Post Older Post Home. Therefore, Moment of inertia of the bar, I is. Sunday, 26 June experiment The values of a and the power b can be found by the method you have used see full theory below.

practical physics: experiment BIFILAR SUSPENSION

In addition, the moment of inertia can be further determined by bifiilar representation from data collated in the experiment. Measure the gradient, m and calculate the y-axis intercept, c of your graph. Equation 4 aforementioned above can be modified to: Note the there are 15 holes bored, hence its introduction in equation 8. Moment of inertia values. The rectangular bar was then detached from the apparatus arrangement and taken to weight balance in order to determine the mass of the bar.

The beam should oscillate in the horizontal plane only. From this, the periodic time was also calculated.

Math The Bifilar Suspension advertisement. The bifilar suspension technique offers the opportunity to determine the radius of gyration of a body by relating the readings gotten from the procedure in the techniques and relating that into the equation of angular and this invariably provides the determination of the moment of inertia for the same body.

In addition an enclosed-type measuring tape and weight balance were also used for the experiment. Repeat to obtain another 10T measurement and then calculate the average of your two measurements. The moment of inertia determined using the analytical approach was approximately equal to the value determined from test 2 in table 2 above.

All measurements and data bifiar were collated for experimental analysis.